3DLac Spray Glue
For perfect adhesion to the printing bed
- Suitable for all materials
- Without perfume
- Resistant to elevated temperatures
- Strong fixing agent
Item no.: 3DL-145, Content: 400 ml
EAN: 8411322235803
- Suitable for all materials
- Without perfume
- Resistant to elevated temperatures
- Strong fixing agent
Product information & technical details
Item no.: | 3DL-145 |
---|---|
Manufacturer No.: | 145 |
Manufacturers: | 3DLac |
Content: | 400 ml |
Product types: | 3D Printer Accessories |
---|
Description
3DLac is a spray adhesive glue for plywood. The spray was developed by a Spanish laboratory specifically for 3D printers FDM processing.
3DLac is without perfume. It is resistant to elevated temperatures and includes a strong fixing agent for improved adhesion to the building board.
Hazard and precautionary statements
Signal word : Danger
Precautionary statements:
- P101 - If medical advice is needed, have product container or label at hand.
- P102 - Keep out of reach of children.
- P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P211 - Do not spray on an open flame or other ignition source.
- P251 - Do not pierce or burn, even after use.
- P264 - Wash thoroughly with plenty of water after use.
- P280 - Wear protective gloves/protective clothing/eye protection/face protection.
- P305+P351+P338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- P410+P412 - Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
- P501 - Dispose of contents/container according to proper regulations.
Hazard statements:
- H222 - Extremely flammable aerosol
- H229 - Pressurized container: may burst if heated
- H319 - Causes serious eye irritation
- H336 - May cause drowsiness or dizziness
Questions & Answers about 3DLac Spray Adhesive
Customer Reviews
| | 80 | (87%) |
---|---|---|---|
| | 9 | (9%) |
| | 1 | (1%) |
| | 0 | (0%) |
| | 1 | (1%) |
91 reviews
6 customer reviews in English
54 customer reviews in all languages
-
-
Stress Tech
Rated with 4 out of 5 stars.
Dry's very quick, so you will need to spray it on as soon as you start printing you first layer. Sticks good and it's easy to clean. No pungent smell like hair spray. Smell does not linger for long too.
Was this review helpful? (1) (0)
-
Review written by John
Rated with 5 out of 5 stars.
perfect what more can i say thanks
Was this review helpful? (0) (0)
-
Review written by Andrew
Rated with 5 out of 5 stars.
always use this item it does what it says on the tine and never fails to work
Was this review helpful? (1) (1)
-
Works excellent with ASA directly 6mm aluminum Modix Big60 V2 print bed
Rated with 5 out of 5 stars.
I've been struggling and searching A LOT for a good combination to print ASA successfully in my Modix Big60 V2 printer (with full enclosure).
In the end, to my stupid surprise, just spraying 3DLac on the aluminum and heating up the bed to 80ºC gives the strong sticking effect I needed!
And the hotter you go, the harder it sticks.
I've noticed that from 70ºC it gave a really good on a BuildTak Flex System, but my objects kept bending the spring steel sheet from the magnets :-(
With wide objects (that need a nice long time per layer) you should really keep the fan off (otherwise lots of internal stress and warping).
But the narrower you go (less time per layer), the more fan speed works ok (even up to 90%), which I need to use to make details and overhangs in fast layers come out good.
And the best of all; after cooling down (from approx 45ºC) it just lets go completely (from the shrinkage of the aluminum bed)?!
I found that it works the easiest even without a brim, as the brim kept sticking to the aluminum, even after cooling down. This is because it can easily deform aluminum bed shrinks, while a more solid object will shrink differently than the bed and come loose.
I'm really very satisfied! I just need to make a simple carton box/frame to limit where the spray will reach, so I won't get spray the inside of my machine too much.
Haven't tried yet, but I expect more materials will stick equally good.
Time will tell.Was this review helpful? (0) (0)
Did you know?
It is already possible to create prints using materials such as titanium, ceramics, wood, and many more.
Recent Articles:
Explore 3DJake:
3DJake Shopping Highlights
-
Free Delivery to United Kingdom from £42.90
-
Delivery in 5 - 10 working days.
-
Free Returns
-
We ship globally to more than 90 countries
-
Secure Payment using SSL Encryption Technology
Review
Rated with 5 out of 5 stars.
Very impressed
Was this review helpful? (1) (0)